GHV3 Operation Manual
Introduction
Please read the "Notes" page before use.
Annotations and Action Images
Click: Press and immediately release a button.
Long Click: Press and hold a button for about 2 seconds, then release.
Hold: Keep a button pressed down.
Twist: Rotate the hilt approximately 90 degrees to either side and then return it.
Stab: Perform a thrusting motion with the blade held horizontally.
This content is an operation manual for Golden Harvest V3 Phase 4 3.34 (as of September 24, 2023). Please note that operations may vary slightly depending on the version.
Basic Operations
| Item | Operation Method | Notes |
|---|---|---|
| ON (Activation) | Click button while stopped. | Exits sleep mode if in sleep mode. |
| OFF (Deactivation) | Hold button while active. | |
| Motion ON | Activate without using a button by performing a strong swing while stopped. | Cannot be activated while in sleep mode. PREON effect is triggered. |
| Motion OFF | Deactivate without using a button by twisting while active. | POSTOFF effect is triggered. |
| Force Effect | Twist while holding the button during activation. | Force sound + effect occurs. |
| Blaster Block | Click while active. | Blaster sound + effect occurs. |
| Lockup Mode | Immediately after a long click while active, strike the hilt. | Lockup effect + lockup sound occurs. (Maintained until lockup mode is released) |
| ┗Release Lockup | Click while in lockup mode. | Lockup mode is released. |
| Stab | Perform a forward thrusting action while active. | An effect where only the tip lights up occurs. |
| Melt Mode | Immediately after a long click while active, perform a stab action. | An effect where only the tip lights up occurs. (Maintained until melt mode is released) |
| ┗Release Melt Mode | Click while in melt mode. | Melt mode is released. |
| Volume Adjustment Mode | Long click while stopped with the blade pointing downwards. | When selected, a "Volume Control Activation" voice prompt plays. |
| ┣Volume Adjustment | Twist the hilt to adjust the volume. | Twist (left/right) to adjust the volume up or down. |
| ┗Confirm Volume | Click button to confirm. | A "Volume Adjust" voice prompt plays. |
| BGM Playback Mode | While stopped, press button + twist (activated when blade is not pointing downwards) | When activated, BGM will play. *Only for sound fonts with BGM. |
| ┣Change BGM | Twist while in BGM playback mode. | The currently playing BGM will switch. |
| ┗Stop BGM | While playing, press button + twist (activated when blade is not pointing downwards) | The currently playing BGM will stop. |
| Reset (Enter Sleep Mode) | Hold button for 10 seconds while stopped. | Enters sleep mode. |
| Battery Check Function | Activate by holding the button and stabbing while stopped. | Reads out the current battery percentage. *Battery check measures in 10% increments. |
| Font Change Mode | Long click the button when stopped. | When selected, a "Sound Menu" voice prompt plays. |
| ┣Select Font | By clicking the button or rotating the hilt right or left. | You can select a sound font. |
| ┗Confirm Font | Hold button while in Font Change Mode. | Confirms the font. |
Saber Editor Function
The Saber Editor function allows you to change saber settings without needing to access the SD card.
| Item | Operation Method | Notes |
|---|---|---|
| Saber Editor Function | While stopped and the blade is pointing downwards, hold the button and twist to enter the Saber Editor menu. | When entering Saber Editor mode, a "Saber Editor Select Mode" voice prompt plays. Click to select various modes within the menu, hold to confirm a mode. |
| ┣① Color Profile | You can set the blade LED color. ① After confirming, first select the font to change (choose sound font). ② After selection, click to switch the function to be rewritten. Switch the color of each function by twisting. (Loops through Blade Base Color / Clash Color / Stab Color / Lockup Color / Melt Color / Blaster Color / Force Color) ③ Hold to exit the color profile and return to the Saber Editor menu. |
When selecting the menu, a "Color Profile" voice prompt plays. |
| ┣② Ignition Type | You can set the blade ignition (ON) effect. ① In mode, first select the blade style to change (choose blade style). Change blade style by twisting, confirm by clicking. ② After selection, twist to select the ignition pattern (choose ignition type). Change pattern by twisting, hold to confirm and return to the Saber Editor menu. |
When selecting the menu, an "Ignition Type" voice prompt plays. |
| ┣③ Retraction Type | You can set the blade retraction (OFF) effect. The editing method is the same as ② Ignition Type. |
When selecting the menu, a "Retraction Type" voice prompt plays. |
| ┣④ Ignition Speed | You can set the blade ignition (ON) speed. ① In mode, first select the font to change. ② After selection, "Ignition Speed" will play, then twist left and right to adjust the ignition speed. ③ After holding to confirm, return to the Saber Editor menu. |
When selecting the menu, an "Ignition Speed" voice prompt plays. |
| ┣⑤ Retraction Speed | You can set the blade retraction (OFF) speed. The editing method is the same as ④ Ignition Speed. |
When selecting the menu, a "Retraction Speed" voice prompt plays. |
| ┣⑥ Gesture Control | Select Gesture Control and hold to enter the mode. ① Press the button to select Stab, Swing, Twist Ignition (ON), and Twist Retraction (OFF). ② Long click to confirm and control ON/OFF. ③ Hold to return to the Saber Editor menu. |
When selecting the menu, a "Gesture Control" voice prompt plays. |
| ┣⑦ Effect Font Slot | Select the effect font slot* and long click to proceed. ① Twist to select the effect font slot set on the SD card. ② After long clicking to confirm, it will be OFF. The set effect will be assigned upon restart. |
When selecting the menu, an "Effect Font Slot" voice prompt plays. For Neopixel models, please set it to one of slots 7-9: "Neopixel Basic", "Neopixel Default", or "Neopixel Extended". |
| ┗⑧ Save | Long click to exit Saber Editor. *You can also enter the mode by pointing the blade downwards and clicking while in the menu. |
When selecting the menu, a "Save Saber Editor" voice prompt plays. |