XENO3 operating instructions and precautions
Introduction
This page summarizes how to operate the XENO3 class provided by LGT SABERS.
Compared to XenoPixel V2, it is now possible to enable/disable some functions, allowing for more flexible customization.
Additionally, the addition of a countdown sound when holding a button improves operability on models without button LEDs.
Please check the page regarding precautions before using.
Annotations and action images
Click: Press the button and immediately release it.
Hold: Press and hold the button.
Twist: Rotate the button approximately 90 degrees to the left or right and then return it.
Push (stub): Make a thrusting motion with the blade horizontal.
Pull: Perform a pulling motion with the blade horizontal. 
Motion image (*Reference source: FETT263)
Method of operation
| item | Method of operation | Feature Description |
|---|---|---|
| Cancel sleep mode (activation) |
Hold the button for about 2 seconds during sleep mode (when the button LED is off). | A voice will say "Power ON" and sleep mode will be canceled. |
| ON (start) | Click the button while stopped. | Start the saver. When sleeping, please cancel sleep mode first. |
| Motion ON | Push (stub) while stopped. | It can be turned on (started) by motion without using a button. |
| Change to next font | Hold the button while stopped. | The font sound will sound and the program will move to the next set font (sound source). |
| change to previous font | While stopped, twist with the blade side facing downwards. | Move to the previous font (sound source). |
| BGM playback/ Stop |
While stopped, twist with the blade side facing above the horizontal. | The BGM set for each font will be played. BGM will stop if it is currently playing. *This will not work with fonts that do not have BGM installed. |
| Volume change function | While stopped, hold the button and release the button when the button LED flashes once*. | You can adjust the volume of the saver. Volume can be adjusted from 3 levels: High (large), Volume Low (small), and Mute. |
| Effect change function | While stopped, hold the button and release the button when the button LED flashes twice*. | You can change the blade effect while the saver is activated. ① Steady (simple) → ② Unstable (unstable) → ③ Rainbow Blade (rainbow light emission) → ④ Candy Blade (rainbow light emission 2) → ⑤ Crack Blade → ⑥ Pulse (slow flash) → ⑦ Flash Blade (fast flash) → ⑧ Fire Blade (flame) You can choose from. |
| Blade mode change function | While stopped, hold the button and release the button when the button LED flashes 3 times*. |
You can change the light emitting effect (Pleon function) and blade pattern when the saber is activated. |
| Sleep mode function | While stopped, hold the button for about 10 seconds until you hear "Power OFF". The font will change during the process, but please continue to hold. |
Go to sleep mode. While in sleep mode, the device enters a power-saving state and does not accept any operations unless you cancel sleep mode. The button LED turns off when the device enters sleep mode. Or, it will automatically switch after a certain period of time has passed in the OFF state. |
| OFF (stop) | Hold the button during startup. | Moves to saver OFF state. |
| Motion OFF | Twist to turn off (stop) during startup. | It can be turned off (stopped) by motion without using a button. |
| Blaster function | Click the button during startup. | When activated, a blaster effect and blaster sound will occur. |
| Flash-on-crash (FoC) function | Gives a shock to Hilt during startup. | When activated, a crashing sound and a flashing blade will occur. |
| Lock-up function | Inflicts a crash while holding the button during startup. | When activated, a lock-up sound and lock-up effect will occur. The lockup is released by releasing the hold. |
| drag function | Hold the button during startup, and release the button when the button LED flashes once. | A drag effect will occur where only the tip of the blade will blink. |
| lightning block mode | During startup, press and hold the button while pulling (pulling the hilt). | When activated, a lock-up sound and lightning block effect will occur. |
| ┗Mode release | Click the button while in lightning block mode. | Cancels lightning block mode. |
| Color change function | Hold the button during startup, and release the button when the button LED flashes twice. | Move to color change mode where you can change the blade color. During color change mode, the blade color will change over time. |
| ┗Color determination (mode released) |
Click the button with the color you want to set. | Decide the blade color and cancel the mode. |
| force sound | While starting up, hold the button and twist with the hilt above horizontal. | When activated, blade effect + force sound will be activated. *This does not occur with fonts that do not have force sound. |
|
RGB ⇔ PIXEL switching (Abolished in v1.2 migration FW) |
While stopped, hold the button until you hear "RGB to PIXEL". (about 15 seconds) You may need to change the font or turn off the power during the process, but please continue to hold. |
Performs switching operations between Inhilt LED mode and Neopixel mode. Not normally used. |
* Regarding the Bluetooth connection function of XENO3, technical compliance certification cannot be confirmed, so there is a possibility of violation of the Radio Law. For this reason, we do not recommend its use.
About changing settings
The motion function, motion sensitivity, countdown sound when holding a button, and blade mode function can be changed by changing the settings.
Please see below for how to change the settings of XenoPixel V3.
XENOPIXEL V3 Settings Manual
Last updated: December 24, 2023