Inhilt LED (XRGB) Operation Method
Introduction
This page summarizes how to operate the Inhilt LED (XRGB) class provided by LGT SABERS.
This model uses the same board as the higher-class XENO3 for built-in LEDs. It comes with 16 different fonts.
Please check the precautions page before using.
Annotations and Action Images
Click: Press and quickly release the button.
Hold: Hold down the button.
Twist: Rotate the button 90 degrees to the left or right and then return it to its original position.
Push (stab): Hold the blade horizontally and perform a thrusting motion.
Pull: Pull the blade horizontally.
Motion image (Source: FETT263)
Access
item | Access | Functional Description |
---|---|---|
Sleep mode release | Hold the button for about 1 second while in sleep mode. | A voice will sound saying "Power ON", Sleep mode will be canceled. |
ON (start) | Click the button while stopped. | Start the saver. If the device is in sleep mode, please cancel the sleep mode. |
Motion ON | Activate by stab or swing while stopped. | It can be activated by motion without using a button. |
Font change (next) | While stopped, hold the button until you hear the font sound. | Move on to the next font set. Loop through all 16 fonts. |
Font change (before) | While stopped, perform the twist operation with the blade pointing downwards. | Move to the previous font set. |
Volume change function | Hold the button while stopped, Release the button when the button LED flashes once. |
You can adjust the volume of the saver. * Models without button LEDs will switch between low volume, high volume, and high volume for approximately 0.5 seconds. You can choose from three levels of mute. |
Effect change function | Hold the button while stopped, Release the button when the button LED flashes twice. |
You can change the lighting pattern when the saver is activated. *For models without button LEDs, the cycle goes from ①Steady (simple illumination) to ②Unstable (high-speed pulse) for approximately 1.0 seconds. ③ You can select from Pulse (Fluctuation). |
FoC setting switching | Hold the button while stopped, Release the button when the button LED flashes four times. |
Switches the FoC (Flash on Crash) function ON⇔OFF. *For models without button LED, it will last for about 2.0 seconds. When turned OFF, no crash effects or crash sounds will be generated upon collision. When this occurs, you will hear an audio message saying "Crash OFF (or Crash ON)". |
Sleep mode function | While stopped, hold the button for approximately 10 seconds until the button LED goes out. | A voice will sound saying "Power OFF" and the device will enter sleep mode. (The font will change during the process, but please keep holding the button.) In sleep mode, the device is in a power saving state and will not turn off unless the device is released from sleep mode. No operations are accepted. Or, it will automatically switch to OFF mode after a certain period of time has elapsed. |
OFF (stop) | Hold the button during startup. | The saver will turn off (lights off). |
Motion OFF | Twist or pull stab while activated to activate OFF (stop). | It can be activated by motion without using a button. |
Smooth swing function | Perform a swing operation while the device is running. | A swing sound will occur. |
Blaster Function | Click the button during startup. | When activated, it produces blaster effects and sounds. |
Flash on Crash (FoC) feature | Shock the hilt while it's activated. | When activated, it produces a crash effect and crash sound. |
Lock-up function | Hold the button during startup Release the button when the button LED flashes once. |
When activated, a lock-up sound and effect will be heard. *For models without button LED, it will last for about 0.5 seconds. |
Color change function | Hold the button during startup Release the button when the button LED flashes twice. |
You will hear the voice say "Color Change" and the device will switch to color change mode, where you can change the blade color. *For models without button LEDs, the blade color will change over time during the mode for approximately 1.0 second. |
┗Color selection | Click the button with the color you want to set. | Decide the blade color and release the mode. |
*Regarding the Bluetooth connection function using the Xeno Configurator, our model does not have a radio wave oscillation function, so it cannot be used regardless of the software settings.
Previous versions of the manual
Inhilt LED (RGB-X) Model Custom Lightsaber Operation Manual
Last updated: August 6, 2024