Proffieboard Operation Manual Beta version ProffieOS7.14
Last updated: 2024/05/14
*This is a version currently under testing and has not yet been reflected in the retail version.
Introduction
This page summarizes how to operate a custom lightsaber equipped with Proffieboard V2.2 or V3.9.
Please check the page regarding precautions for custom lightsabers before using them.
About Annotations and Motion
- PWR: Power button
- AUX: Auxiliary button
- Click: Press and quickly release the button.
- Double-click: Click the button twice quickly.
- Long click: Press and hold the button for about 1 second and then release it.
- Hold: Press and hold the button.
- Twist: Rotate the hilt 90 degrees to the left or right and then return it to its original position.
- Stab: A straight thrusting motion.
- Push: Perform a slow horizontal push and pull motion.
Motion image diagram (Reference: FETT263)
Operation manual (one-button model)
This is a manual for a one-button model that can be operated with a single button.
| item | Function Description | How to operate |
|---|---|---|
| ON (start) | Turns the OFF saver ON. | Click the button while stopped. |
| OFF (stop) | Turns the saver that is ON into OFF state. | Hold the button while it boots up. |
| Gesture ON/OFF | Activate ON/OFF without using a button. | Twist when stopped to start, twist when starting to stop. |
| Blaster | Blaster sound + blaster effect occurs. | Click the button during startup. |
| Lockup | Lockup sound + lockup effect occurs. | Hold down the button while launching to cause a crash. (The blade must not be pointing downwards.) |
| stub | The tip of the blade emits a stab effect. | During activation, the blades are held parallel to each other and thrust. |
| Melt | A melt effect occurs, causing the tip of the blade to glow. | Hold the button while launching and perform a stab. |
| drag | A drag effect occurs where the tip of the blade glows. | Hold down the button while launching to cause a crash. (The blade must be pointing downwards) |
| Font Change | Change the font (sound source) being set. | Next font: Long click the button while stopped Previous font: Hold the button while stopped |
| Force Action | A force sound will be played when activated. | Hold button and twist while booting. |
| Multi-Blast Mode | When in Multi-Blast Mode, swinging will cause a blaster effect. | Hold the button and swing while it's running to start the mode. Click the button while in mode to cancel the mode. |
| Lightning Block | When activated, the blade will have a lightning block effect. | Double-click and hold the button during startup. |
| Color Change Mode | This will switch to color change mode, where you can change the blade LED color. | While activating the device, hold the button with the hilt facing down and twist. When this occurs, a sound effect will play and the game will transition to color change mode. *Some special effects may not be able to change colors properly. |
| ┗Color selection | Change the blade LED color. | Rotate the hilt while in this mode to select a color. |
|
┗Color selection (mode off) |
Decide the blade color and cancel color change mode. | Hold the button until you hear a sound effect on the designated color. |
| BGM playback mode | Play background music set for each font. | Double-click the button while stopped. |
| ┗BGM stop | Stops the background music that is playing. | Double-click the button while in BGM playback mode. |
| Volume Adjustment Mode | You can adjust the volume of the saver. | While stopped, hold the button and crash to enter the mode. |
| ┗Volume up | Increase the volume setting. | Click the button during the mode. |
| ┗Volume down | Turn down the volume setting. | Long click during mode. |
| ┗Volume determination | Determine the volume and release the control volume. | Crash while holding the button during the mode. |
Operation manual (2-button model)
This is a manual for a two-button system consisting of a PWR and AUX button.
| item | Function Description | How to operate |
|---|---|---|
| ON (start) | Turns the OFF saver ON. | Click PWR while stopped |
| OFF (stop) | Turns the saver that is ON into OFF state. | Click PWR during startup |
| Mute ON | It starts in muted mode. | Double-click PWR while stopped |
| Gesture ON/OFF | Activate ON/OFF without using a button. | Twist while starting or stopping |
| Blaster | Blaster sound + blaster effect occurs. | Click AUX during startup |
| Multi-Blast Mode | When in Multi-Blast Mode, swinging will cause a blaster effect. | Long click AUX while running to start the mode. Click Crash or AUX while in mode to cancel. |
| stub | The tip of the blade emits a stab effect. | During startup, perform a crash with the blades facing parallel. |
| drag | A drag effect occurs where the tip of the blade glows. | While the device is running, hold the AUX button with the blade pointing downwards and perform a crash. Or, hold AUX with the blade facing downwards. |
| Melt | A melt effect occurs, causing the tip of the blade to glow. | While starting, hold AUX with the blade above parallel and perform a stab. Maintains melt while holding. |
| Lockup | Lockup sound + lockup effect occurs. | Hold AUX while starting up to vibrate the hilt. Or hold AUX with the blade in any position other than downwards. |
| Force Action | A force sound will be played when activated. | Long click on PWR during startup. |
| Force Push | A motion action causes a force action. | Push the blade while it is running. |
| Lightning Block | The blade has a lightning blocking effect. | While booting, hold PWR and click AUX. Keep the Lightning Block while holding PWR. |
| Color Change Mode | Change the blade LED color. |
While the blade is booting, hold AUX and click PWR (like pressing AUX and then PWR). Rotate the hilt to select the color. *It will not activate if the blade is facing up. Some effects may not change color properly. |
|
┗Color selection (mode off) |
Decide the blade color and cancel the mode. | Click PWR in the mode with the given color |
| ┗Color reset (mode release) | Resets the color to the color when color change mode is activated and cancels the mode. | Click PWR in the mode with the given color |
| Multi-Phase Preset Change | Change the font without turning off the blade. | While booting, press AUX and twist. |
| Battery check | Reads the remaining battery level as a percentage. | While stopped, press and hold AUX and click PWR |
| Gesture ON/OFF | Motion action control can be turned on/off. | While stopped, press and hold PWR and twist. |
| Preset Scroll Modes | You can change the sound source using motion actions. | Long click AUX while stopped (A voice will say "Select Preset" when switching) |
| ┗Preset Move | Change to a preset (font). | Rotate hilt right: Move to next font Rotate hilt left: Move to previous font Adding a PWR hold will jump to the next (or previous) font. |
| ┗Sound source decision | Confirm the preset (font) and exit the mode. | Click PWR while in preset scroll mode |
| ┗Set as default sound source | Move to preset 1 (initial position preset). | Click AUX while in preset scroll mode |
| Font Change | Change the font (sound source) being set. |
Next preset: Click AUX while stopped Previous preset: Click AUX while stopped with the blade in the down position |
| BGM playback | Play background music set for each font. | Long click PWR while stopped |
| ┗BGM stop | Stops the background music that is playing. | Long click PWR while stopped and BGM is playing |
| Battle Mode Switch | Enables/disables Battle Mode. | While it's running, press and hold AUX and swing to turn it on/off. |
| Battle Mode | During battle mode, relevant actions will be automatically activated depending on the situation. | When Battle Mode is ON, the following actions are activated: |
| ┗Auto lockup | A lock-up effect occurs. | When the blade is not pointing downwards, apply a crush and maintain the crush position. |
| ┗Automelt | A melt effect occurs. | When the blade is not pointing downwards, the stub + stub position is maintained. |
| ┗Auto Drag | A drag effect occurs. | With the blade facing downwards, keep the stub + stub position |
| ┗Blast Effect | Blaster effect occurs. | Click AUX and swing within 2 seconds to activate the blaster action in Multi-Blast mode. |
| Volume Adjustment Mode | You can adjust the volume of the saver. | While stopped, press and hold PWR and click AUX. |
| ┗Volume adjustment (mode off) |
Adjust the setting volume. | You can adjust the volume by rotating the hilt. Left rotation: Small volume Right rotation: Large volume |
| ┗Volume setting (mode off) |
Determine the volume. | Click PWR or AUX |
| Effect Change Mode (New) | You can change the lighting pattern. | While booting, press and hold AUX and long click PWR (press and release for about 1-2 seconds). When the effect change is activated, the saber will briefly go out and mute after the sound effect, then re-light the base of the blade with the changed effect. The effect that is changed will cycle through the effect patterns of the font currently set in the saver. |
Reference video
others
The ProffieOS used is 6.9. (As of May 2023)
You can see the Proffieboard-equipped lightsabers at the following link:
Please see the link below for past Proffieboard manuals.