Inhilt LED (RGB-X) Operation method and precautions
This page is the operation manual for In-hilt LED (RGB-X) sabers.
In-hilt LED classes have different operation methods depending on the version. If your board color is black (XRGB), please refer to the operation table below.
NEXUS XRGB Custom Lightsaber Manual | SYBERSABERS
List of products equipped with In-hilt LEDs
In-hilt LED Model Custom Lightsaber List | SYBERSABERS
■ Introduction
Please read the precautions page before use.
Notes and Action Images
Click: Press the button and release immediately.
Hold: Press and hold the button.
Twist: Rotate the hilt about 90 degrees to either side and return it to the original position.
Push (Stab): Perform a stabbing motion with the blade held horizontally.
Pull: Perform a pulling motion with the blade held horizontally.
Motion Image (*Reference: FETT263)
Operation Methods
The button LED blinks in 0.5-second increments.
If you release the button when the button LED has blinked 3 times, it means you release the button 1.5 seconds after pressing it.
| Item | Operation | Description |
|---|---|---|
| Wake from Sleep Mode | Hold the button for about 1 second while in sleep mode. | The audio will say "Power ON," and sleep mode will be deactivated. |
| ON (Ignition) | Click the button while the saber is off. |
Ignites the saber. |
| Motion ON | Perform a stab or swing motion while the saber is off. | Allows ignition via motion instead of the button. |
| Change Sound Font (Next) | Hold the button while off until the font audio plays. | Switches to the next font set. |
| Change Sound Font (Previous) | Perform a twist motion while the blade is pointing down while off. | Switches to the previous font set. |
| Volume Change Function | Hold the button while off and release when the button LED blinks once. | Adjusts the saber volume. You can choose from Volume Low, Volume High, and Mute. |
| Effect Change Function | Hold the button while off and release when the button LED blinks twice. | Changes the blade ignition effect. Select from ① Steady, ② Unstable, or ③ Pulse. |
| Motion Control Toggle | Hold the button while off and release when the button LED blinks 3 times*. | Toggles motion control actions*. *Motion-based font change, ON, and OFF functions. Audio will confirm "Motion Control OFF" or "Motion Control ON." |
| FoC Setting Toggle | Hold the button while off and release when the button LED blinks 4 times*. | Toggles Flash on Clash (FoC) ON/OFF. When OFF, collision effects and sounds are disabled. Audio will confirm "Crash OFF" or "Crash ON." |
| Sleep Mode Function | Hold the button while off for about 10 seconds until the LED turns off. |
The audio will say "Power OFF," and the saber will enter sleep mode.
|
| OFF (Retraction) | Hold the button while ignited. | Turns the saber OFF (retracts the blade). |
| Motion OFF | Perform a twist or pull-stab motion while ignited. | Allows retraction via motion instead of the button. |
| Smooth Swing Function | Swing the saber while ignited. | Generates a smooth swing sound. |
| Blaster Function | Click the button while ignited. | Triggers blaster effects and sounds. |
| Flash on Clash (FoC) | Impact the hilt while ignited. | Triggers clash effects and sounds. |
| Lockup Function | Hold the button while ignited and release when the button LED blinks once. | Triggers lockup sound and effect. |
| Color Change Function | Hold the button while ignited and release when the button LED blinks twice. |
The audio will say "Color Change," and the saber enters color-changing mode. |
| ┗ Confirm Color | Click the button at the desired color. | Sets the blade color and exits the mode. |
| Color Change (Quick) | Hold the button while ignited and release when the button LED blinks 3 times. | Enters color-changing mode. Similar to the standard color change, but cycles quickly through primary blade colors. |
| ┗ Confirm Color | Click the button at the desired color. | Sets the blade color and exits the mode. |
Last updated: 2024/12/16