In-hilt LED (XRGB) Operation Guide (Legacy Version)
Introduction
This page summarizes the operation methods for the In-hilt LED (XRGB) class provided by NEXUS.
This is a model that utilizes the board used in the higher-end XENO3 class, adapted for In-hilt LED use. It comes equipped with 16 sound fonts.
Please refer to the following for the list of fonts.
The contents of this manual are subject to update or change without notice.
Please check the page regarding safety precautions before use.
Safety Precautions | ATTENTION
Annotations and Action Images
Click: Press the button and release immediately.
Hold: Press and keep holding the button.
Twist: Rotate the hilt about 90 degrees to either the left or right and return it to its original position.
Push (Stab): Perform a thrusting motion while holding the blade horizontally.
Pull: Perform a pulling motion while holding the blade horizontally.
Motion Image (*Source: FETT263)
Operation Methods
| Item | Operation Method | Function Description |
|---|---|---|
| Wake from Sleep Mode | Hold the button for about 1 second while in sleep mode. | A "Power ON" voice prompt will play, and sleep mode will be deactivated. |
| ON (Ignition) | Click the button while the saber is off. | Ignites the saber. If in sleep mode, please perform the wake-up operation first. |
| Motion ON | Perform a stab or swing motion while the saber is off. | You can ignite the saber using movement (motion) without using the button. |
| Font Change (Next) | Hold the button while the saber is off until you hear the font voice. | Moves to the next font set. Cycles through all 16 fonts. |
| Font Change (Previous) | Perform a twist motion while the blade is pointed downward while the saber is off. | Moves to the previous font set. |
| Volume Change Function | Hold the button while off, and release when the button LED flashes once. | Allows you to adjust the saber's volume. *For models without a button LED, this is about 0.5 seconds. You can choose from three levels: Volume Low, Volume High, and Mute. |
| Effect Change Function | Hold the button while off, and release when the button LED flashes twice*. | Allows you to change the blade's lighting pattern while ignited. *For models without a button LED, this is about 1.0 seconds. You can choose from: ① Steady, ② Unstable (fast pulse), ③ Pulse (flicker). |
| FoC Setting Toggle | Hold the button while off, and release when the button LED flashes four times*. | Toggles the FoC (Flash on Clash) function ON or OFF. *For models without a button LED, this is about 2.0 seconds. When OFF, collision effects and clash sounds will not occur. You will hear a "Crash OFF" (or "Crash ON") voice prompt. |
| Sleep Mode Function | Hold the button for about 10 seconds while off until the button LED turns off. | A "Power OFF" voice prompt will play, and the device will enter sleep mode. (It may cycle through fonts during the hold; please continue holding.) In sleep mode, power is saved, and no operations will be accepted until the wake-up sequence is performed. The device will also enter this mode automatically if left off for a certain period. |
| OFF (Shutdown) | Hold the button while the saber is ignited. | The saber will power down (extinguish). |
| Motion OFF | Perform a twist or pull motion while ignited. | Allows you to extinguish the saber using motion without using the button. |
| Smooth Swing Function | Swing the saber while ignited. | Produces swing sounds. |
| Blaster Function | Click the button while ignited. | Triggers blaster effects and blaster sounds. |
| Flash on Clash (FoC) Function | Impact the hilt while ignited. | Triggers clash effects and clash sounds. |
| Lockup Function | Hold the button while impacting the hilt while ignited. | Triggers a lockup effect (entire blade flashes) and lockup sounds. |
|
Color Change Function * |
Hold the button while ignited and release when the button LED flashes twice*. | A "Color Change" voice prompt will play, entering the mode where you can change the blade color. *For models without a button LED, this is about 1.0 seconds. In this mode, the blade color will cycle over time. |
| ┗ Confirm Color | Click the button when the desired color is reached. | Sets the blade color and exits the mode. |
* Currently, the XENO3 (XRGB) color change function cycles through three colors simultaneously; therefore, some fonts that utilize mixed colors (e.g., RGB=(255,255,255)) may not produce pure red (255,0,0) or blue (0,0,255).
Previous Manual Versions
In-hilt LED (RGB-X) Model Custom Lightsaber Operation Manual
Last Updated: April 29, 2025