Proffieboard Operation Manual (Old Version)

※This page is for the manual version prior to late March 2025.

For the latest version, please refer to the following:

[March 2025 Edition] ProffieOS 7.15 Custom Lightsaber Operation Manual

Introduction

This page provides instructions on how to operate lightsabers equipped with Proffieboard.

Proffieboard is a high-performance soundboard that combines advanced sound and effect control, high customization flexibility, and open-source expandability.

The operating procedures described on this page are based on the standard operating patterns set by our store at the time of shipment.

Please read the "Custom Lightsaber Precautions" page before use.

Precautions | ATTENTION

Notes and Motion Images

Motion image diagram (※Reference: FETT263)

Operation Manual (1-button model)

This manual is for 1-button models operated with a single button.

Item	Function Description	Operation Method
ON (Activate)	Turns the saber ON from an OFF state.	Click the button while stopped.
OFF (Deactivate)	Turns the saber OFF from an ON state.	Hold the button while active.
Gesture ON/OFF	Activates/deactivates ON/OFF without using buttons.	Twist (or swing on some models) to activate while stopped, twist to deactivate while active.
Blaster	Produces blaster sound + blaster effect.	Click the button while active.
Lockup	Produces lockup sound + lockup effect.	Hold the button while active and apply a clash. (Blade should not be pointing downwards)
Melt	Produces melt effect with blade tip illumination.	Hold the button while active and perform a thrust motion while holding it horizontally.
Drag	Produces drag effect with blade tip illumination.	Hold the button while active and apply a clash. (Blade should be pointing downwards)
Font Change	Changes the currently set font (sound).	Next font: Long click the button while stopped. Previous font: Hold the button while stopped.
Force Action	Plays a Force sound upon activation.	Hold the button + twist while active.
Multi-Blast Mode	In multi-blast mode, swinging the hilt generates a blaster effect.	Hold the button + swing to start the mode while active. Click the button to exit the mode.
Lightning Block	Produces a lightning block effect on the blade.	Double-click and hold the button while active.
Color Change Mode	Enters color change mode to change the blade LED color.	While active, point the hilt downwards, hold the button, and twist. A sound effect will play upon activation, and the saber will enter color change mode. ※Color may not change correctly with some special effects.
┗Color Selection	Changes the blade LED color.	Rotate the hilt to select a color while in mode.
┗Color Confirmation (Mode Exit)	Confirms the blade color and exits color change mode.	In the desired color, hold the button until a sound effect plays.
BGM Playback Mode	Plays BGM set for each font.	Double-click the button while stopped.
┗BGM Stop	Stops the currently playing BGM.	Double-click the button during BGM playback mode.
Volume Adjustment Mode	Allows adjustment of the saber's volume.	Hold the button + clash while stopped to enter mode.
┗Volume Up	Increases the set volume.	Click the button while in mode.
┗Volume Down	Decreases the set volume.	Long click the button while in mode.
┗Volume Confirmation	Confirms the volume and exits volume adjustment mode.	Hold the button and clash while in mode.

The button program used is SA22C.

Operation Manual (2-button model)

This manual is for 2-button models with PWR and AUX buttons.

Item	Function Description	Operation Method
ON (Activate)	Turns the saber ON from an OFF state.	Click PWR while stopped.
OFF (Deactivate)	Turns the saber OFF from an ON state.	Click PWR while active.
Mute ON	Activates in mute (silent) mode.	Double-click PWR while stopped.
Gesture ON/OFF	Activates/deactivates ON/OFF without using buttons.	Twist (or swing on some models) to activate while stopped. Twist to deactivate while active.
Blaster	Produces blaster sound + blaster effect.	Click AUX while active.
Multi-Blast Mode	In multi-blast mode, swinging the hilt generates a blaster effect.	Long click AUX while active to start the mode. Clash or click AUX to exit the mode.
Drag	Produces drag effect with blade tip illumination.	Hold AUX while active with the blade pointing downwards.
Stab	Produces stab effect with blade flickering.	Perform a thrust action while active and the blade is horizontal.
Melt	Produces melt effect with blade tip illumination.	Automatically activates when stabbing a wall while active. While melting, rotating the hilt changes the tip color.
Lockup	Produces lockup sound + lockup effect.	Hold AUX while active and apply vibration to the hilt. Or hold AUX when the blade is not pointing downwards.
Force Action	Plays a Force sound upon activation.	Long click PWR while active.
Lightning Block	Produces a lightning block effect on the blade.	Hold PWR and click AUX while active. Lightning block occurs while PWR is held.
Color Change Mode	Changes the blade LED color.	Hold AUX and click PWR while active. (Imagine pressing PWR immediately after AUX) Rotate the hilt to select a color. *Does not activate if the blade is pointing straight up. Color may not change correctly with some effects.
┗Color Confirmation	Confirms the blade color and exits the mode.	Click PWR at the desired color while in mode.
┗Color Reset	Resets to the color active when color change mode was entered and exits the mode.	Click AUX while in mode.
Multi-Phase Preset Change	Changes fonts without turning OFF the blade.	Hold AUX and perform a twist motion while active.
Battery Check	Announces battery level as a percentage.	Hold AUX and click PWR while stopped.
Gesture ON/OFF	Enables/disables motion action operations.	Hold PWR and apply an impact (clash) to the hilt while stopped.
Preset Scroll Mode	Allows changing sound fonts via motion actions.	Long click AUX while stopped. (A "Select Preset" voice will play upon entering this mode.)
┗Preset Navigation	Moves to a different preset (font).	Rotate hilt right: Move to the next font. Rotate hilt left: Move to the previous font. Holding PWR during these operations will jump 5 fonts forward (or backward).
┗Font Confirmation	Confirms the preset (font) and exits the mode.	Click PWR while in preset scroll mode.
┗Set to Default Font	Moves to Preset 1 (initial preset position).	Click AUX while in preset scroll mode.
Font Change	Changes the currently set font (sound).	Next preset: Click AUX while stopped. Previous preset: Click AUX while stopped with the blade pointing downwards.
BGM Playback	Plays BGM set for each font.	Long click PWR while stopped.
┗BGM Stop	Stops the currently playing BGM.	Long click PWR while stopped and BGM is playing.
Battle Mode Toggle	Toggles Battle Mode ON/OFF.	Hold AUX and swing while active to toggle ON/OFF.
Battle Mode	In Battle Mode, relevant actions are automatically triggered based on the situation.	The following actions activate when Battle Mode is ON.
┗Auto Lockup	Produces a lockup effect.	Apply a clash and maintain the clashed position when the blade is not pointing downwards.
┗Auto Melt	Produces a melt effect.	Perform a stab and maintain the stabbed position when the blade is not pointing downwards.
┗Auto Drag	Produces a drag effect.	Perform a stab and maintain the stabbed position when the blade is pointing downwards.
┗Blast Effect	Produces a blaster effect.	Click AUX and swing within 2 seconds to enter multi-blast mode, triggering blaster action.
┗Force Push	Force action occurs via motion.	Perform a push action.
Volume Adjustment Mode	Allows adjustment of the saber's volume.	Hold PWR and click AUX while stopped.
┗Volume Adjustment (Mode Exit)	Adjusts the set volume.	Volume can be adjusted by rotating the hilt. Rotate left: Volume down Rotate right: Volume up
┗Volume Confirmation (Mode Exit)	Confirms the volume.	Click PWR or AUX.
Effect Change Mode	Allows changing the light pattern.	Hold AUX and long click PWR (press and hold for about 1-2 seconds then release) while active. When effect change activates, a sound effect will play, the saber will briefly turn off + mute, and then re-illuminate from the base of the blade with the changed effect. The effects will cycle through the patterns available for the currently set font on the saber.
Gesture ON/OFF (New)	Toggles the active/inactive state of Gesture ON/OFF.	Hold PWR and apply an impact to the hilt while stopped.

The button program used is FETT 263.

Reference Video

 

Others